And it has some options to interpret data following strict W3C standards. Which was incredibly helpful when learning, as it encouraged me (and a lot of others) to don’t go down the IE/Netscape and later Chrome “specialities” road. (Yes,I am that old…I still remember MS fucking FrontPage)

And then he will be a dead Hopefully. Through Vanguard and Blackrock the Saudis and Qataris are said to have substantial investments in Tesla. And especially the former are not kind people when it comes to fraud to their disadvantage.

Often reverse osmosis works better - and distillation systems require a lot of upkeep and energy costs. So there is that. And of course they only help if it’s not their transport system.

First of all: Where in your system was the sample taken? At the well? At a tank? At a faucet?

The answer to this question is important for the next steps.

Be aware that high lead content can also be an issue for plant watering and even showering.

If the sample has been taken at a endpoint (faucet) I would try to get another sample at the well directly. If you are “lucky” the acidity of the water is the reason lead is brought into your system from a section of your transport system. In that case replacing the transport layer (basically: Get new pipes) is the best approach - while it’s not cheap it is also not as expensive as filtering (or dealing with the health issues from lead, especially in the US).

If the well shows the same values you are screwed. There are basically two scenarios then: Your well installation itself is the problem - this is in theory “fixable” but expensive, but you might accidentally even poisoning your neighbours then. (The way to find out if it’s your installation is either with specialised equipment or, for some confirmation, get a sample from a neighbour who ideally life upstream from you)

If it’s not your well installation then it’s the well itself…and then you really really need a more extensive analysis: Lead in a ground water deposit is somewhat rare and often a indication something else is problematic - both because geologically lead is often next to other nasties, but also because human caused pollution with lead often goes with the real nasty stuff like arsenic,etc. And you really would want to find these. Then shit sadly becomes really expensive.

Nope,it hasn’t. If your glasses are fogging up in sync with your respiration rate or within a very short timeframe your mask is not sealing. Period. The only difference is when you have either have a valve mask, work with a face shield or similar things or in confined spaces - it’s basically impossible to fog up your glasses with a correctly positioned mask as the filter medium does work as a diffuser. If your mask does fog up suddenly despite a confirmed fit it usually is a warning sign for a breakdown of the filter medium.

(And believe me, we tried really hard - as part of a customer contract we tested all major mask manufacturers available in the EU, with a sample size in the 4 digit range, including UV fluid and thermal imaging tests)

I am fully aware that the equivalent of N95 is often seen as comparable to FFP2, but this is not actually quite correct. The FFP2 has a slightly worse filtration rate and a slightly higher resistance both for inspiration and expiration. Anyway, I intentionally wrote FFP3 as this is the recommended FFP class for Measles while within the NIOSH legislation only a N95 is recommended.

Mhm. Hard. Due to the fact that engineering is split into subspecialties in most of Europe the “general purpose engineer” is often unknown. And for civil and fire protection work you would need a local degree to prove you know the codes. (Which tbh are vastly different).

But trying and failing is better than never trying + this is not my field and I just repeat what I gathered from friends in these fields.

The European union never had any intention to be limited to land borders within Europe and explicitly understand themselve as a economic and trade, ethical values and international cooperation based union - which by the way does include far tighter equal defence rules than the NATO accords. This is especially important as Europe is not a well defined geographical area and its borders are somewhat fluid.

Remember that before Erdogan Türkiye was considered as a possible member, Cyprus is a member, Georgia was on its way to a membership before the current government took a tour to Moscow, etc. The longest single country-to country land border the EU has is the French-Brazil border.

And Canada has as much of a border to a EU country(but not the EU as Greenland is not part of it) as e.g. Türkiye has it’s European parts. So after all…this is not an issue at all.

Besides Denmark there is also France - and incidentally this border is also the closest sea border the French have to any other country: Saint Pierre et Miquelon. But the collectivité d’outre-mer that they are formally not part of the EU but only EU associated. But France could easily change a single law to make them part of the EU. So if that is a criteria that is nothing that can’t be overcome.

Beside that we would fucking love to have Canada in the EU. I have yet to find a single EU citizen who has a problem with that idea.

Very much depends on your speciality in engineering - US engineering in some fields is world-class,in some fields it’s,well, developing world. Very much depends on your field, therefore.

Mostly yes,but it is possible to have some beardstyles if you know very much what you are doing (and have a large head).

But the actual area of contact and to a certain degrees the areas around it need to be shaved properly,yes.

Every vaccination has a (although very slim) chance to cause an adverse reaction. Around 5% of all people vaccinated have a minor skin reaction (which is physiological and not an anaphylaxis. 1% report joint pain.

But,more severely, 1-4 people out of a million develop a life-threatening anaphylaxis, 3 out 100.000 a serious blood clothing disorder. Very rarely(as in: Less than 1 in 1 Million), but with a slightly higher incidence of you are an adult pancreatitis and deafness is reported.

As medicine is always a game of chances we try not to risk things,even if they are rare.

Healthcare professional here - but not your HPC and you cannot confirm that I am who I am so double check what I write:

• Get your titers checked and get revaccinationes asap. If you are not vaccinated or are a non-responder talk to your healthcare provider. Isolate until then.

• Mask up and keep your hands away from mouth, eyes and nose. You will need a properly fitting FFP3/NP95 mask here - measles are far meaner in terms of infectiousness than COVID. Tight fitting means: You have no leaks at the side - if your glasses fog up, if you can feel air going in or out next to your face,etc. it is not working. The usual “duckbill” masks with straps around the ears very very rarely fit properly.

• Wash your hands and desinfect them properly.

• Stay the fuck away from babies. Really. Please.

Centauri Carbon might be worth a look into then - it can print fairly high temperature filaments.

Yes and no. Old job was more IT and process related, nowadays I work more in disaster planning , public health policy and process planning in healthcare, spiced up with a bit of medical intelligence.

Basically hospitals, large companies and government bodies are legally required to have plans for major incidents (from “hey,there has been a train collision, you get 30 severely injured in 20min” to “shit,we lost all power” or “IT outtake”) - we do the planning and training, including life exercises for you. You want to update your healthcare system/the placement of your prehospital resources(ambulances, etc.) as a state or government body? We do that that for you.

You need to know which hospital in a random African country is the right one for a tourist with a sudden rare disease or your insurance wants to know how safe it is to send on of your staff members someone right into the current emerging disease hotspot? We do that for you.

Well, I got fired from a very stupid company (who would have guessed that healthcare companies needs more assistance instead of less during COVID? Not them.) when COVID hit.

Started my own company from the severance,so basically I hired myself and created my own job…and a few more.

Couldn’t be happier.

You are really surprised by a guy who wanted to name his car series S-E-X-Y and had a temper tantrum when model E was taken and he could not “buy” it.

I personally would start with TPU(after PETG) - the different shore grades provide a large usability for a lot of things and it print comparably well once you find the right calibration. Especially with a A1 as you mentioned you have one.

To be honest I would skip ABS totally in an A1 unless you have an external enclosure with a good filtering and exhaust solution. Be aware of the noxious fumes ABS will produce that have a potential to intoxicate you and are suspected to cause cancer depending on the additives. (Among others ABS produces hydrogen cyanide when printed - which is often better known under it’s former German brand name: Zyklon B…)

ASA nowadays provides a far less problematic (but not unproblematic) solution and while it’s a little bit more complicated to print it’s still manageable depending on the filament manufacturer. But you will need a temperature stabilised enclosure for both anyway, while ASA is a bit more sensitivitie,it doesn’t really matter that much for me.

Within ASA I personally found a far larger bandwidth of printability between the manufacturers. The major manufacturers for PLA often suck - especially Bambu Lab ASA is hideous to print. If you are in Europe I cannot recommend the Black Forest Filament ASA enough, their stuff is not comparable to any other ASA I printed. Alternatively material4print. If you need a filament that is available worldwide Filamentum Apollo X is a solid choice, so is Polymaker,but both to a lesser extend.

In theory PMMA, PCTG and CPE are also worth a consideration, but besides CPE all of them are far more difficult to print.

BTW: All variants need to be printed very dry, ideally out of a warm dry box.

You can easily kill yourself with a water overdose (and it’s actually fairly common),so yes.

Nutmeg was already mentioned - high doses can easily kill someone, sadly even without hallucinations simply by killing off ones liver and dying an agonizing death a few days later. The same goes for cinnamon, but with a much lower dose.

There are a few more, but I don’t want to give people too many ideas.

To make it short: Yes, possible,but it’s mostly a very slow death over multiple days that fucks you up really bad and is a horrible way to go.

Sadly the hallucination effect does not correlate with the toxicity,especially the hepatotoxicity with nutmeg… You can absolutely kill of your liver and die an agonizing death a few days later and have no hallucinations at all.

Tbf, comparing blender and openscad is more like comparing a hammer with a knife.

FreeCAD would be the more obvious comparison here - and while Openscad has some benefits for more complicated projects it is less than optimal - and sadly FreeCAD still sucks compared to most commercial products,even though it has improved recently due to the ONSEL influence.