That surprises me, but I suppose it had to work for some listeners or they wouldn’t have gotten it past testing. I have even tried clearing my listen history and starting over - still comes up with country and (going to clarify) ‘metal’ . I like rock and alternative and some forms of pop, as well as a bit of hip hop. cannot fathom why it suggests what it does.
What is rym?
I have started buying vinyl with the digital downloads when I find a great album. I feel better doing it this way. Most of my music is not super big name artists.
I know this does not make me look good - but I am a YouTube Premium subscriber. I had Spotify, but they jacked up their family plan rate, and it was only a few bucks cheaper than Premium, then I got the ad-free (without adblockers). I mostly did it to help my kids avoid the toxic ads that are littered into the kid content. The main reason I stick with some of this stuff is for the discovery. Pandora was great, Spotify is ok.
Regardless - the smart playlists, and AI stuff on YouTube music is AWFUL. I cannot put into words how bad it is. Spotify got it right about 1/4-1/2 of the time. YouTube, maybe 1/100. Constantly recommending a country, which I cannot stand. When it isn’t doing country, it recommends hard rock/metal which I also do not listen to. I feel like I need a new way to find music, then I could sever ties with all these trashy subscriptions.
I forgot until looking at your photo that the mini uses a Bowden tube, not direct drive like the MK3S+. Did you replace/switch the nozzle around the time this all started happening? With Bowden tubes, there are a few problems that can arise that you don’t see on direct drive. The end of the Bowden tube (that is inside the extruder/hote end assembly) can get deformed or clogged. If you can check that, you may find an issue. Other than that, when swapping nozzles I always had to put the nozzle in part of the way, then push the Bowden in further, then tighten the nozzle.
My money would be a clogged nozzle. But a better photo (close up) may be helpful. Things I wonder…
Does the filament come out and curl back up during preheat?
Is your heat block messy with residue?
Have you tried a cold pull, or pulling the nozzle and cleaning/replacing it?
Not sure what that means. I never get any messages from TMO unless it’s a bill notification…
Amen.
deleted by creator
What is an appimage?
When I first started working with 3d modelling (for 3d printed parts), I followed everyone’s advice and got a trial of Fusion. Luckily, I didn’t use it much and when I came back to it, my trial was over. I did not want to use a hobbyist license, just to have things change - so went looking for FOSS alternatives. OpenScad made my brain hurt, but then I found FreeCAD. Definately hard to learn, and for someone new to CAD design - I am learning very slowly.
I watched a ton of videos, but still struggle. My saving grace was that I found the official discord. The users on the discord server can be super helpful with learing the nuance of the platform. Several times I posted a file and askded for help and had an answer within an hour. In fact, I just submitted a screenshot of my sketch with dimensions and someone went ot the trouble of recreating it and fixing my problem…so I recommend you join the server if you are struggling. Link below:
Yes and on some printers, that spot where the Bowden tube meets the nozzle is very problematic. You have to loosen the nozzle a bit, push the Bowden tub up against it, then tighten the nozzle the rest of the way
It was awful on my Ender clone, but haven’t had that issue on my Prusa.
I have tried to jumpstart a few communities by posting and commenting regularly . I would try a new one, but if people do not find or join, it will get caught in the same cycle as the existing groups. I like participating, but am not interested in being the single driving force, or moderating.
To answer your other question, I cannot stand when I see auto mirrored content from Reddit. I usually ignore those posts, as I have rarely seen comments happening. When the content wasn’t created by somebody here, I don’t think anybody is invested in maintaining or participating in the discussion.
I think you may have misunderstood. I have FOUND communities, but there is not much engagement or activity. I have resorted to discord channels for most of them, but it is not the same.
Some of my most active subreddits were different 3d printing and 3d modeling groups, groups for games like Overwatch, and Payday. Different AI focused groups, but specifically groups like the Stable Diffusion sub, Subreddits that discuss my favorite shows, or styles of music. None of that is active here. It isn’t that they don’t exist on Lemmy, they are just ghost towns. I joined multiple instances and am very active and engaged on multiple accounts, on some of these groups - but there is not response. I was in the top 3% of karma earners on Reddit - and I did that by submitting and commenting a lot. That just doesn’t happen here (yet).
I gotta be honest…I am hanging on by a threat. The communities that I was engaged with on Reddit before the Snoopacolypse were pretty niche. I wasn’t there for r/funny or r/videos, etc. I found similar communities on Lemmy, but they have soooooo little activity. I have to modify my sort just to see content, as its so old. When there are posts, they typically get very little discussion.
I am on Lem.ee, and I have the hardest time posting anything from mobile. It looks like it fails, and if I sort by new, it isn’t there and never shows up - HOWEVER, I start getting replies, so someone is seeing it somehow.
I detest what reddit did and is still doing - but Lemmy is not filling that void for me, and its frustrating.
I had to dig to find where I got the model from. I suppose I should add the link in case anybody wants to give them kudos or print it for themselves.
It was created by Rocket Pig Games: Printables link
That is a very good question. There aren’t any insane overhangs, just a few tricky spots. I had print he same thing smaller, so I knew it would be okay. I think the file actually mentioned in the notes that you COULD print it without support.
Can I ask what settings you had to hone in?
What printer and hot end?
Every time. I am not sure it actually changes anything. I have submitted feedback and bug reports to YTM as well. Just generic replies.